Structural stress
Contents |
[edit] Introduction
A material under stress is in a state that has resulted from the application of a force or forces. These forces can also be called stresses. The effect on the material will depend on the type of stress that is applied.
Stress patterns in structural elements can be complex but they usually comprise just three basic types of stress:
- Tensile.
- Compressive.
- Shear.
[edit] Tensile stress
If the stress acting on a structural member tends to make it longer, it is said to be under tensile stress or 'in tension'. The load carried by each unit area of the member’s cross section is the tensile stress in the member. This will make the member a ‘tie’. Steel is ideally suited to resist tensile stresses and is used widely in construction for this purpose, for example to reinforce concrete, or in the form of cables, wires and chains.
For more information see: Tension.
[edit] Compressive stress
If the stress acting on a member tends to result in it shortening (its components are pushed together), it is said to be under compressive stress or 'in compression'. The load per unit area of the member is the compressive stress. This makes that member a strut, or if the member is large, it might be a column, pier or stanchion, depending on its position in a structure. Most materials can carry some compressive stresses – other than cables, wires, chains and membranes.
For more information see: Compression.
[edit] Shear stress
Shear stresses make the particles of a material slide relative to each other and usually result in deformation. An example is a riveted connection which can shear when excessive force is applied. Vertical forces acting on a cantilever can make it shear off at the wall junction. Shear forces produce shape deformation in materials eg, a rectangular element can be contorted into a skewed parallelogram. The shear stresses are those acting on the planes along which the sliding takes place and are measured across a unit area.
For more information see: Shear.
[edit] Units of stress
The N/m2 is the basic SI unit of stress but is very small for most purposes. As a result, MN/m2 may be used, often expressed as N/mm2 in structural codes for steel, concrete and timber.
[edit] Related articles on Designing Buildings
- Bending moment.
- Compression.
- Concept structural design of buildings.
- Bearing capacity.
- Failure of cast iron beams.
- Lateral loads.
- Limit state design.
- Moment.
- Point of contraflexure.
- Racking.
- Rebar.
- Shear.
- Shell roof.
- Structural principles.
- Structural steelwork.
- Strut.
- Tensile strength.
- Tensile structures.
- Tension.
- Ties.
- Types of structural load.
Featured articles and news
BSRIA Briefing 2024: Sustainable Futures speakers
Redefining Retrofit for Net Zero Living 22 Nov.
Wall of support for post-Grenfell regulation of electricians
Call for a shake-up of the construction industry highlighted on radio.
Digital sustainability through future AEC tools
Bringing together industry and academia to meet challenges.
Skills gap for net zero highlighted to Minister for Industry
ECA convenes roundtable discussion at Portcullis House.
Evidencing Net Zero with the new UK buildings standard
Pilot version with detailed excel proforma out now!
Scottish Building Safety Levy, in consultation
From direct remediation and the RPDT, to the costs and alternatives.
Waves of warmer homes grants for the rental sector
Boosting energy efficiency standards for all rented homes.
A refocus of the National Planning Policy Framework
Key terms described in brief, as the consultation closes the evening of the 24th.
Fortified farmhouses of the unruly 16th-and 17th-century borders.
ECA shares advice for those who may be exposed to risks.
How to revolutionise UK housing with MMC
CIC and Supply Chain Sustainability School unveil a plan.
From the UKs largest manufacturer and supplier of lime.
From mud bricks to smart concrete
A brief history from 7000BC to a future on the moon.
Regulator of Social Housing publishes latest fire safety report
Covering remediation of 11 metre plus social housing sector buildings.
Apartment and Duplex Defects Remediation Bill 2024
Approved for priority drafting by Government of Ireland.
The long list with in the frame of key historical events.
Competence frameworks for sustainability in the built environment
Code of practice, core criteria consultation draft for comment.
New Floods Resilience Taskforce
With a wet met office autumn prediction.